How To Align Rifle Scope With Bore: An Ultimate Guide

If you are searching for how to align rifle scope with bore, our article might help. Click on today to learn the step-by-step guide on boresighting your range.  

Aligning the rifle lens with bore

Aligning the rifle lens with bore

Shooting a rifle is a job that requires meticulousness and seriousness. Before firing real bullets, we need to align the rifle scope to ensure accuracy. You need to check your zero to ensure it’s still in place.

So, how to align rifle scope with bore sighting? Please follow these steps:

  • Mount your scope.
  • Boresight your rifle.
  • Attach the bore.

To learn more about each step in detail, continue reading the article here!

Reading more:

How To Align Rifle Scope With Bore? Step-By-Step Guides

To be able to understand each step in the process of aligning the gun lens, you will need to take a few steps as follows.

Gun scopes

Gun scopes

Mounting Your Scope

The first action you should take is to tighten any screws associated with the conduit. You will slowly adjust in small increments to create even pressure across the scope and receiver.

With guns that have separate scope rings and sights, you’ll need to degrease the top of the receiver and apply a thin coat of nail polish to most of its surface. Be careful because it will affect the whole gun if you install the bolts incorrectly.

The force applied to the screws will depend on their type and size.

As for the screw rings, you’ll have to screw them in very carefully. Using too much force can rupture the bronchoscope through the delicate internal clusters.

A torque converter will significantly assist you during screwing.

During tightening the screw, make sure you have placed it in a sturdy area and have plenty of support. You also need to pay attention to crosshair alignment as it can change during execution.

Eye relief is also a particular issue. Move the lens from the eye side about three to four inches until you see the entire field of view.

Make sure that the vertical grid of the scope and the vertical axis of the rifle are aligned, then tighten the ring screws.

Reading more:

Boresighting Your Rifle

Zeroing your rifles

Zeroing your rifles

The tools needed for this crucial stage are a gun and a standard or laser lens alignment kit. Depending on your needs, you can choose between two devices.

Standard kits are highly compatible with most standard calibers. The laser borehole rangefinder is easy to use and saves time. It is highly suitable for rifles with muzzle breaks.

Start by aiming about 25 yards away from you and the gun. Then place your weapon in the clone position and remove the turret cap from your range.

If you use the scope attached to the ballistic turret, carefully study that space’s zero stop and adjustment mechanism.

From here, remove the gun’s pin, look down at the bore, and start aligning. Our goal is to center the bull with the center of the drill hole of the device.

If your reticle is skewed to one side, align the windage turret to the other side to bring the reticle back to balance.

You will also have to make similar adjustments to the height of the lens. If your tile is below the center, move your elevation turret down to move your tile upwards.

Reading more:

Attaching The Bore

Once you’ve adjusted your lens, reattach it to your gun and aim at your target.

Under the standard toolset view, you’ll see a grid. All you should do is place the reticle in the center of the grid.

Conversely, the laser indicator will project a bright dot onto the target. You can adjust the turrets to aim precisely where you need to shoot.

This 25-yard adjustment can help you aim for the paper at 100 yards.

One trick is to hit 1 inch low at 25 yards. This number is beneficial during alignment because the aiming height on the barrel of most rifles is 1.5 – 2 inches.

Frequently Asked Questions

If you still have any questions about bore sighting rifle scopes, find the answers in this section.



What Distance Should A Laser Bore Sight Be?

To reproduce the target, one can use assistive devices such as a collimator or laser boresighter.

Laser bore sight devices will emit corresponding lasers to hit the target for about 25 yards, always in a safe direction.

Many put the laser measuring device on the muzzle end of the barrel, and others put it in the rifle’s chamber like a dummy ring.

Reading more:

How Far Back Should Scope Sit On Rifle?

When mounting the lens, pay attention to the problem that eye relief drops from low to high power. Please ensure that this distance is sufficient for humble power observation but still able to maintain a wide eye-lens width at high magnifications.

The optimal distance of scope from your gun is between three and four inches. It will make sure the device doesn’t poke your nostrils.

The main reason for a reticle is that you need to focus on the ocular lens (eyepiece) on every new lens. This adjustment will help keep the reticle sharp under your eyesight for accurate shots.

How Far Off The Barrel Should A Scope Be?

The lens should be positioned as close to the bore line as possible for most uses. This problem is entirely separate from the cheek weld. With optics for combat purposes, the higher the optical centerline, the longer the effective range.

The recommended distance between the lens and barrel is not less than ⅛ inch of clearance between the bottom of the objective and the tip of the barrel. You can also consider (0.160) for the range base height to have enough headroom.

To learn more about the scope height, check this video below.

How Accurate Is Bore Sighting?

In addition to some benefits such as ease of use and reasonable price, bore sighting is entirely accurate when aligning targets.

Boresight at 25 yards, borehole view, and range adjustment allows easy target alignment within 100 yards.

The most accurate device is the laser boresight. Instead of aligning by eye, the laser device guides you through the adjustment process.

Related post:

Final Thoughts

How to align rifle scope with bore? We hope that this article has given you a satisfactory answer. Check the gun’s zero range regularly to ensure accuracy.

We wish you a successful hunting season!


Leave a Reply

Your email address will not be published. Required fields are marked *